| |
|
|
|
There’re many connection modes of CPE for various demands: it can connect to computer, connect to
hub, or connect to router.
After choose CPE connection mode, you may start the CPE installation
|
|
|
|
Make sure your CPE off before the installation, and the installation steps are as follows:
1. Rotate the antenna 180 degrees by clockwise direction, and make sure the antenna is fixed by
adjusting the antenna lock nut.
2. Insert the RJ45-connector of the Ethernet cable into the computer’s Ethernet interface, and
insert the other RJ45-connector of the Ethernet cable into the CPE’s Ethernet interface.
3. Insert one end of the power adapter connection line into the power supply interface on the side
of CPE, and plug the other end into the 220V AC power socket.
3. Press the CPE power button, and state is “On”. If the power indicator light is off, there should
be something wrong with CPE or power adapter, please check the equipment connections carefully.
4. Observe the CPE signal strength indicator light: CPE is searching the network if the light is
flickering; CPE has accessed the BS if the light stops flickering.
If the light has been flickering for a long time,
Rotate the CPE or antenna, Move the CPE to the place near window or a higher place.
|
|
How to connect to the internet |
|
1. Press start button and click on run or press win + R
In run window type ncpa.cpl and press ok then Network Connections window will open
2. Under Lan or High speed internet you should be able to see Local Area Connection
Right click on it and select properties.
3. In general tab find Internet protocol (TCP/IP) and select properties
Put ticks to “Obtain an IP address automatically” and “Obtain DNS server address automatically” and press OK
Close the Local area connection properties window
4. Now your computer will be trying to acquire an ip from the system if everythin goes fine you can see two computers on the right hand side of your taskbar is blinking
Open internet explorer or any other browser your using and you should be able to see Globe Internet 4G Broadband Mobile Internet login page
|
|
How to log in and log out |
|
|
|
1) Confirm the LAN connection as follows.
•Is the power lamp of your LAN card lit?
••Have you successfully obtained an IP address by DHCP?
2) Launch your web browser.
Login authentication is conducted using the web browser.
Note: You need to disable your proxy setup
3) Type in a URL. For example, http://www.globemw.net
4) Type in your user ID and password on the user ID/password page
5) Now enjoy broadband access!
|
|
|
|
1) Type in the URL for the logout page. Access the logout page by typing http://4g.globemw.net in the upper space of your browser.
2) Click the log off button. When the page shown, click "OK".
3) Now, logout is complete.
4) How to log in again. After closing your browser, launch the browser again or type in http://www.globemw.net/ in the upper space of your browser. When the login page appears, follow the normal steps to log in.
Note: If the login page does not appear even when you type in http://www..globemw.net/ and the 4G Broadband Internet homepage is still showing on the screen, some data may be remaining in the browser cache. Clear the cache first, and try to access again.
|
|
When I open my Web Browser, the log-in page does not come up |
|
Check that your LAN Card is propery inserted. |
|
|
|
Windows XP/200 Users
1. Go to Start>Settings>Control Panel
2. Double-click Network Connection
3. Right-click Local Area Connection and select Properties
4. Check the TCP/IP box and click Properties
5. Choose the option Obtain an IP Address Automatically
6. Choose the option Obtain a DNS Server Address Automatically
7. Click OK to exit the Properties Window
8. Click OK until you are out of the Control Panel Settings
|
|
I have typed in myUsername and Password but i cannot log on |
|
Make sure you have the typed in the correct Username and Passord |
| |
